KL Jewelry Design’s Jewel School Contest Entry

Please visit JTV  to vote on my entry in the Jewel School Contest.  This is a photo of the piece I entered.  Thanks.

 

Swirling Galaxy Ring

I was watching JTV this last Sunday and one of my favorite jewelry artists was on, Dale “Cougar” Armstrong.  She was showing off a new ring design she had created using square wire and some crystals.  I always love seeing what Dale comes up with and figuring out something a bit different to make it my own design.  So here goes another free tutorial for you as one of my blog readers or Facebook fan.

Swirling Galaxy Ring
Created by Kris Penney, Designer/Owner
KL Jewelry Design
Materials
6-6mm or smaller beads
3 pieces of 21 gauge square wire of your choice each piece 41/2″ long
1″ 20 gauge half round wire of your choice
 
Tools
Flat nose pliers
Round nose pliers
Flush cutters
Emery file
Ring mandrel
Rawhide or nylon hammer
Polishing cloth
Masking Tape
Fine tip marker
 
Step 1
Cut 3 pieces of 21 gauge square wire to 41/2″ in length.  Using the polishing cloth clean and straighten each piece.
 
Step 2
Tape the ends of the bundle of wires together and mark the center of the wire. 
 
 
 
 
 
 
Step 3
With the 20 gauge half round wire and your flat nose pliers make a hook on one end.  The end of your hook should be at a slight angle so you have something to hold onto while you are wrapping the bundle wires. 
 
 
 
 
 
Step 4
With your non-dominate thumb hold the wrap wire just to one side of the mark on the bundle wires and with your dominate hand wrap the wire around the side of the bundle wires.  With your flat nose pliers press the wrap wire into place. 
 
 
 
 
Step 5
Continue doing this until you have three complete wraps on the outside of the bundle wires.  Be sure to start and end your wraps on the same side of the bundle wires, this is the inside of your bundle wires. 
 
 
 
 
 
Step 6
Trim the wires so they don’t hang out over the edges of your bundle wires and using your flat nose pliers press them into place.  Run your finger over the top to be sure there are no rough spots.  If there are edges you snag your finger on use an emery board to file the edges and smooth them down.
 
 
 
 
Step 7
Place the center of your bundle wires on the ring mandrel 1/2 size smaller than your final ring size.  with the ring mandrel pressing against your table edge (I do this by putting the largest end of my mandrel against my stomach and the tip against the table and pushing into the table this holds the mandrel in place leaving my hands free to form the ring. 
 
 
 
Step 8
Holding onto the wires push or pull them around the ring mandrel 1/2 size smaller than your finished size so if you want a size 8 ring place your wires at 71/2 on the mandrel.  Continue shaping the wires around the mandrel until they meet at the center. 
 
 
 
 
Step 9
Start your swirl by moving both ends of your bundles tightly around each other. 
 
 
 
 
 
 
Step 10
Continue with the swirl until you have gone all the way round and your wires are now all the way around the swirl.  Remove the tape.
 
 
 
 
 
Step 11
Fan the ends out as you see in the photo.  Try to get them as evenly spaced as you can going around the center swirl.
 
 
 
 
 
Step 12
Slip one of your beads onto any of the wires.  I am using 6 mm beads but in the photo with the red beads I used the largest size of seed beads (E bead) and got a much tighter swirl for those that don’t like “big” rings.
 
 
 
 
 
Step 13
At the very tip of your round nose pliers form a simple loop in the end of the wire.
 
 
 
 
 
 
This wire is just a little bit too long so trim the wire until you have 1/4″ sticking out past the bead.  Now form another loop.  Continue doing this until you get all your beads on and the wires looped.  Sometimes you will have a wire that is short but if you life the wire up from the center swirl you can slip your bead further down your wire and form the loop.  You want the beads as close to the center swirl as you can get them.
 
 
 
Step 14
Slip your ring back on your mandrel and if you need to use the rawhide of nylon hammer to gently tap the ring to shape it and get it to your finished size.  Your ring should have sprung out to the size you wanted after you did the first swirl.  I started at size 71/2 and ended at a size 8.
 
 
 
 
Now you can enjoy your finished ring.  When I have the ring done I put it on and gently press the swirls to smooth them out on my finger to get the ring to fit how I want.  When I am selling these I skip shaping the ring to my finger but be sure to let your customers know to do this.
 
Here are three samples of my Swirling Galaxy Ring

Musings from Kris

Learn how to make this necklace for free!

 Fields of Green Necklace

 Click on this link if you need a pdf reader.

 http://get.adobe.com/reader/

Check out my Facebook page to see photos of the latest designs. Soon the new pieces will be at http://www.kljewelrydesigns.etsy.com so please do heart me in Etsy and friend me on Facebook http://www.facebook.com/profile.php?id=100001263081321

KL Jewelry Designs’s First Jewelry Giveaway!

Read my post about my giveaway for your chance to win. http://eepurl.com/Gv2H

KL Jewelry Design April News

What I see from my customers…

Recently I did a survey to see what my customers wanted me to write about in my newsletters and the one person that completed my survey told me they would like to know jewelry trends and how to put things together. So here’s my attempt to respond to you and thanks for answering my survey.

According to the market big and chunky jewelry is in this year. Good to know I’ve been fashion forward all along even before it was in. On the whole according to the market I get my information from besides you guys, bright jeweler’s brass is the new gold this year because of the cost of purchasing gold. It is a great alternative to gold jewelry and gives you the look of gold without breaking the bank to get it. 

So far this year I am noticing that my customers are purchasing a lot more brass, silver, and copper jewelry. Not the usual antiqued brass like last year but brass that looks like gold. Is this because gold is so expensive? Maybe; I know purchasing gold filled wire is very expensive for me to purchase which means whatever I make out of it is much more expensive for you to buy from me. 

I know that a lot of women and men think that the only thing to buy when it come to buying jewelry is gold but that is such a limited view; of course that’s just my opinion; but keep reading and let me try to explain myself. 

When you only buy gold jewelry you are missing out on other fantastic metals such as sterling silver argentium silver, copper, colored artistic wire, silver plated colored artistic wire, brass wire, and aluminum wire. Each of these wires has their good qualities and their bad qualities and I try to use all of them when I am making my jewelry. 

I select the wire to compliment the stone. Some wire artists wrap the stone with the idea that the wire is the focus of the piece but I think the stone is still the focus when I am wrapping a stone or creating a ring. The wire is just a means to an end and should compliment the main show.

More

%d bloggers like this: